Wednesday, 7 November 2012

Unfortunately the hull and chassis returned to the museum in my absence so no pictures were taken of them freshly sandblasted, here as you can see they have already been undercoated. 
The freshly primed chassis. 
Left hand side view, the restoration has reached the point where pretty much everything has been stripped down and now it will start being built up. 
Front quarter view. 
Mike Tobolo is hand painting the hard to reach areas on the chassis in the original colour match of Italian grey/green.   
Here he is hard at work. 
The inside of the chassis frame being painted.

Finally the day has arrived to transport the hull and chassis to the sandblasting plant. 
The hull is being winched little by little off the ground. The man to the left is Richard Henry the armour curator.
And here she is a little higher off the ground. Our overhead gantry can only handle kg5000 or 5 tons so care has to be taken not to overload it. 
The truck has pulled in and the hull is being lowered onto the truck. 
A view from further back. 
Next it was time for the chassis to be loaded, these two components were the only ones the museum wasn't able to transport for sandblasting on our own. The other components were broken down and moved bit by bit.
Lashing the hull and chassis to the lorry. 
Pulling out of the gate on the way to the sandblasting contractor. 
There she dissapears down the road.

The primed m.g. mounding. 
Another view. 
Here you can see the m.g. splash guard already sand blasted, this component prevents any bullets that happen to squeeze through the gaps from injuring the crew. 
Another view of the shield. 
And primed waiting for the interior colour. 
One of the turrets side pistol ports being stripped. 
The rotation plate which is relatively free of any contact surface rust, the thick layers of paint are to thank for this. 
Not so with the outer exposed armoured swivel plate. 
The swivel retention plate from the inside. 
This part should have been stripped before the major sandblasting was carried out as can be seen in the surrounding area.

The gimbal mounting ring has been sandblasted. 
This view shows the hard wearing layer of baked on black enamel, even sandblasting hasn't been able to remove the coating. 
All the mg components after sandblasting. 
A close up view of some of the parts, the two discs in the middle are the elevation/depression bearings. 
The armoured shield. 
Looking into the housing after some sandblasting has taken place.
Once again everything was re assembled to have a look how it all fits together and make sure some smaller items haven't slipped through the sandblasting grid. 
Looking into the housing once again. Note that the upper and lower rotation bearings are externally mounted and that the elevation/depression bearings are located on the inner surface. 
A side view. 
The top view, the upper and lower bearings attach the mounting to the armoured car. 
Right hand side view.

The turret rear access hatch, you can see the layers of paint and traces of the various colours that have been applied over the years. 
Some light sandblasting to loosten up the bolts and then the mechanism was removed. 
Here it has all been sandblasted 
This is how the mechanism works. 
A picture out of sequence that shows the stripped down components of the turret mounted periscope. 
The components of the hull machine gun mounting.  
An underside view of the gun locking frame. 
A side view showing the original baked on black enamel colour. 
Looking into the mounting, the tube is for the sighting telescope and the oval slot to accommodate the gun barrel. 
The outer pivoting ring or gimbal mounting. 
And here is the armoured ball that protects everything.

Tuesday, 6 November 2012

Attention was now turned to the periscope mounting bracket that is located inside the turret roof. Here you can see the item already sandblasted.  
A detailed view. 
From another angle. The centre piece slides between the outer rails in a gentle arc, this allows the head of the periscope to be tilted and view various angles. The knurled locking nut can be seen protruding downwards.
Another bit added. 
This is the rough orientation of how it sits inside the exterior bulbous armoured shield. 
I temporarily bolted it to the upturned turret roof to show how it is mounted. 
From this side one can see the swivelling locking nut, you can also see the path of the curved arc. 
The two above photos shows the full swing of the mounting. 
In this closeup the curved groove is clearly seen.
Another view of it mounted inside the turret.